Switches

GBC Ibico 640ID Punch MP2500ix interchangeable die modular operating

GBC interchangeable die punch MP2500ix (before Ibico 640ID) is one of the most impressive modular binding punches on the market. It is a perfect receptacle for the printing of small and medium-sized and small. This blow by blow when finishing with a piece of GBC combined module creates a versatile production system. This article gives some easy instructions to use their MP2500ix GBC Punch.

1st Select a number of die for your MP2500ix and put fully into the system. First, it can eliminate one already, the system.

2nd Determine the number of holes needed for the document and turn off all the pins is not required. The pins are in the select pin deck.

3rd The side guide hole in the table has a number of MP2500ix alignment marks, the position of the right edge guide for a variety of styles and sizes shot match. To adjust the side guide cover sufficient / paper selection, ie. 11 "x 8-1/2" center holes on the role of the top of the bottom of binding, release Lateral guide rotate in the opposite direction. Slide the Side of the correct alignment mark according to your model and the drilling of the selected paper size. Press the button to the lead edge guide in nearby village. Note that the registration of the location of the edge guide and can approximate a small guide to the inner edge of the area for the right to adjust focus marks. It is important that the edge guide is positioned correctly for the paper size / coverage, you are stuck.

4th Turn off the system by pressing the power on / off the unit back on (I). Make sure the light is on. Select a list of small pieces of paper, and vertically in throat punch. Slide the stack of paper all the way to the left against the leadership. Turn the cycle by the Palm handheld or pedal. Remove materials thumb. At determine whether the side guide is adjusted correctly, fold a sheet of paper along the edge of the drill collar. Match the holes on – if the corners of the game without overlapping – the space on the first hole is the same amount of space on the last hole, the alignment is correct. If not, set the side guide (very little – a small movement can make a big difference) and repeat the process until the edges are squared. The coup is now ready for use.

* For Velobind, Follow the above procedure, but if you combine the dual paper in half along the edge of the two holes closest to the "V" are the centerpiece. If the paper is aligned at this point, the game is the well-centered.

* The open design Gorge final blow may MP2500ix the drill sizes, that there is no higher than the maximum width of paper are to be drilled in one operation. Not that several steps are necessary to drill large sheets of paper. A little Experimentation is needed to determine the correct position of the lead edge. You can eliminate some of the beats on the right combinations of paper sizes and types of drilling punch. This can easily and quickly by these instructions are carried out – remove all trees that are used by death

o Identify The stamp will be removed – note, the paper pierced twice – the first half and then the other. To prepare this, first place a sheet of non-standard sizes next DIESET to be drilled. Fold in the middle. Hold the leaf in half pins to determine which pins will be necessary to drill half of the paper.

Remove the extra punch or with a slight pressure on the upper rail of the ensemble. Unlock the final rail hook-pin (nearest the handle set) and the free oscillation of the upper punch. Drag the blows are not necessary. Place the pin hole clip.
Install all die or slide the dice game as described above.

Evidence or several sheets of perforated paper in half on the paper around and punching the other half. Adjust the width guide and / or the number of stamps are required to obtain the desired results.

5th The 640ID uses a variety of easily interchangeable dies, is the versatility of one of the most important Properties of this system makes it so desirable because the operator to create many different images can bind with certain styles. Note: Drill the bottom of each style requires a separate listed since September, except 2-4/3-5-7 all die, that style is loose-leaf collection. A sticker on the handle of each interchangeable die set indicates the punching pattern.

About the Author

Jeff McRitchie is the designer and Director of Marketing for
www.MyBinding.com
. He has written hundreds of articles on topics related to
Binding Machines
,
Modular Puches
, Binding Supplies, Laminators, Laminating Supplies,and more.